CU-K15-IC10 RFID Access Control Card Reader - 13.56MHz

The non-contact proximity card access controller is one of the modern and advanced access control system. It features a large-capacity memory chips, so you can store many information of users on it.

Using this module, you can create a traffic control system. This device allows you to open the entrance door through three methods: using an ID card, entering a password and pressing the bell button.

You can use both normally open and normally closed door lock system (relay).

It has air tight break command. The controller on this unit can detect somebody has tempering at the unit with the alarm.

This product is the ideal device for business organizations, offices, factories, residential, community and other places.

Specificatoins of CU-K15-IC10 RFID Access Control Card Reader - 13.56MHz:

• Technical parameters:
• Power supply: DC 12V ± 10% Current <0.1A
• Dimensions: 116mm x 116mm x 20 mm
• Weight: 130 g
• Ambient temperature: 0 ° C -60 ° C
• Relative humidity 20% -80%
• User card storage capacity: 255, a group of open code
• Reading distance 5-15CM
• Card type EM or EM compatible card (13.56MHz )
• Sound and light indication:
• LED indicator:
• red light green light incident
• normal flashes once per second
• read valid card bright
• reading light illegal card
• bright unlock
• button type bright
• light into the programming
• program to confirm bright
• Built-in Buzzer:
• Event Description beep:
• read valid card twice: short beep beep
• read illegal card: beep sounding once
• type key is valid: a short beep beep
• enter the password twice: short beep beep valid
• password wrong once blew tick -
• confirm programming: two short beeps
• tamper alarm sounding: continuously beep - beep - beep

Usage Notes For CU-K15-IC10 RFID Access Control Card Reader - 13.56MHz:

Hardware setup:

You need at least 4 wires to connect to the controller: 12V, GND*2, Push/NO.

Program setup steps:

the initial password: Programming password is 9999.

1. Enter programming mode:

Press * # to enter programming mode programming code.

2. Feature Sets:

a. modify the programming code:

Press * programming code # 0 # new password repeat new password # *

Note: The password is any number 4-6.

b. increase the user card:

Press * programming code # 1 card reader to enter the Code # *

Note: The card code is 001-999 unrepeatable three digits, you must enter the code, otherwise the card is invalid.

c. Delete user card (there are three ways):

A, according to the programming code * # 20000 # *

Delete all user card;

B, according to the programming code * # * # 2 reader

Deleted card to be read;

C Press * programming code # 2 The card code is # *

Delete lost card;

d. Set open mode:

Press * programming code # 300 # * read valid card to open the door

, press * programming code # 301 # * Reader add a password to open the door

, press * programming code # 302 # * Reader or password to open the door

Note: The factory setting is the reader or the password to open the door;

e. Set open time:

Press * programming code # 4 XX # *

Note: XX is 00 -99 seconds, factory setting is 6 seconds.

f. Set Public Open Code:

Press * programming code # 5 Repeat new password new password # # *

Note: The password is any number 4-6.

Note: The above settings in the last press * before pressing a key interval not more than ten seconds

3. use:

a. Normal operating state reading a valid card to open the door;

b. If you need to read the card with a password , enter within 10 seconds after reading the card the correct password to open the door;

c. If you forget your password programming, you can use the jumper switch on the motherboard "RESET" to restore the factory settings. Turn off the power to the

jumper switch to "ON" position, and then turn on the power, the buzzer beeps three jumpers will switch back to "OFF" position to rest

You can watch this video for using this device.