Search results for: 'rf module arduino'

TTP224 Capacitive Touch Sensor Module Features This 4 Channel Capacitive Touch Sensor Module uses the TTP224 IC and is actually a combination of 4 capacitive touch sensors. This module has 4 outputs, by touching each button from 1 to 4, the corresponding output will be High. There are also 4 LEDs on the module that will turn on by touching each button. TTP224 Capacitive Touch Sensor Module Pinout This module has 12 pins and 4 touch buttons:6 pins on the Right:OUT1: ...

KY-039 Heartbeat Sensor Module Features The KY-039 heartbeat sensor module can be used to detect the heartbeat signal using finger. This sensor has an analog output. By placing your finger on the module, you can see the heartbeat signal through the analog output pin. KY-039 Heartbeat Sensor Module Pinout This module has 3 pins:S: Analog output signalVCC: Module power supply – 5VGND: GroundYou can see the pinout of this module here. ...

HW-M10 Microwave Sensor Module Features The HW-M10 microwave sensor module is very accurate and widely used for motion detection in alarm and security systems. This module, like the PIR module, can detect any movement. The only difference is that instead of using radiation emitted by or reflected from objects, it uses microwave Doppler radar technology. This module has a digital output that is normally Low and becomes High (3.3V) if it detects motion and remains High for 2 to 3 seconds. ...

MPR121 Capacitive Touch Sensor Features The MPR121 capacitive touch sensor module is a high-precision touch sensor. This module has 12 touch buttons and supports I2C communication and can be easily interfaced with any microcontroller. There is no regulator on the board, so the supply voltage should be between 1.7 to 3.6VDC. MPR121 Capacitive Touch Sensor Pinout This module has 18 pins:6 Pins on the left:VCC: Module power supply – 3.3VIRQ: Interrupt outputSCL: Se...

RDM6300 RFID Reader Module Features If you are a little familiar with electronics then you have probably heard of RFID (Radio-Frequency-Identification). The RDM6300 model is one type of RFID modules with 125 kHz frequency. This module is designed for reading code from 125KHz (ID) compatible read-only tags and read/write 125KHz cards.Features:Support external antennaMaximum effective distance: up to 50 mmUart interfaceSmall outline design RDM6300 RFID Reader Module Pin...

If you're looking to interface the INA219 current sensor module with an Arduino, you've come to the right place. In this guide, we'll walk you through the necessary steps to get your setup up and running smoothly. INA219 Current Sensor Module Features The INA219 module is used to measure both current and voltage at the same time. This module uses I2C communication to transfer the voltage and current data. Other features: Measurement accuracy: 1% Maximum measured voltage: 26V Maximum measured current...

AD8232 ECG Module Features The AD8232 sensor can provide you to monitor electrocardiographic or ECG signals. Analyzing these signals prepares useful information about heart function, such as heartbeat rate, heart rhythm, and other information regarding the heart’s condition. This module can be connected to a microcontroller on one side and to specific parts of body on the other side using 3 special electrodes. The signal received through the electrodes can be seen in the analog output of the sensor. ...

Heart Rate Sensor Module Features This module is designed for educational and entertainment purposes and is used to detect Cardiovascular pulse wave with finger. It uses a PPG (HRM-2511E) probe for data transmission. This sensor uses infrared light technology. If the amount of blood changes, the intensity of infrared light will change as well. This heart rate sensor has two analog and digital outputs and one LED for the digital output. You can see the heartbeat more accurately by the analog output. Featur...

MT8870 DTMF Decoder Module Features DTMF stands for Dual-tone-multi-frequency. This module is for sending signals using the voice-frequency band over telephone lines to switching centers. This module has two important applications: First, to specify the desired number to telecommunication through switching centers; second, it is capable of transmitting commands to these centers and other telecommunication devices. Technical specifications: Input voltage: 5V 5mm input jack LED to indicate the binary ...

AD9833 Signal Generator Module Features In many projects we need a signal with a specific waveform and frequency. The AD9833 signal generator module is a low-cost module for such applications. This module is capable of generating sine, triangular, square and half-square waveforms. You can adjust the frequency of generated signal from 1Hz to 12.5MHz. The communication protocol of this module is SPI. AD9833 Signal Generator Module Pinout This module has 7 pins:Ref: Re...