Search results for: 'arduino'

R308 Biometric Fingerprint Module Features R308 biometric fingerprint module is a high-precision, high-performance matching algorithm and high-capacity flash chip. It works based on fingerprint image processing, matching, memory search and performing and desired functions. It uses serial communication in order to communicate with microcontroller. The default Baud Rate is 57600, and it is not possible to change it. This module can store up to 500 fingerprints. You can down...

TM7711 24-bit Pressure Module Features The TM7711 is a 24-bit 2-channel analog-to-digital converter used to measure resistance changes. This module is widely used in load cell and air pressure sensors. This module features high accuracy, quality and cost-effectiveness. Note This module does not support I2C communication. You can download the datasheet of this module here. [wpdm_package id='18020'] TM7711 24-bit Pressure Module Pinout This sensor has 8 pins: VIN: Module power supply – 3.3-5...

R305 Optical Fingerprint Features R305 biometric fingerprint module is a high-precision, high-performance matching algorithm and high-capacity flash chip. It works based on fingerprint image processing, matching, memory search and performing and desired functions. R305 uses serial communication in order to communicate with microcontroller. The default Baud Rate is 57600, and it is not possible to change it. This module can store up to 980 fingerprints. It features a USB cable so you can...

NEO-7M GPS Module Features GY-NEO-7M module is an advanced GPS module that supports UART communication protocol with active antenna. You can interface this module easily with any microcontroller. This module has a rechargeable battery and can also be connected directly to a computer using a USB to TTL converter.This module can receive data and then calculate the geographical position with a very high accuracy and speed. In addition to supporting BeiDou, Galileo, GLONASS, GPS / QZSS, the module has inter...

NEO-8M GPS Module Features The GY-NEO-8M module is an advanced GPS module based on uBlox m8N that supports UART communication protocol with active antenna. You can interface this module easily with a microcontroller. This module has a rechargeable battery and can also be connected directly to a computer using a USB to TTL converter.NEO-8M can receive information and then calculate the geographical position with very high accuracy and fast speed. In addition to supporting BeiDou, Galileo, GLONASS, GPS / ...

MX1508 Motor Driver Module Features The MX1508 driver is one of the cheapest drivers for running DC motors with a maximum current of 2 amps. Small dimensions and simple setup are the positive features of this module. The MX1508 is a dual full-bridge motor driver that allows two DC motors to be connected simultaneously. Note The MX1508 motor controller follows the H-bridge configuration, which is handy to drive a stepper motors.This driver has a temperature protection circuit that disables the d...

TCRT5000 IR SENSOR Features The TCRT5000 sensor consist of an IR transmitter and IR receiver. When the proper voltage is applied to the infrared transmitter, it transmits and emits infrared waves. When these waves collide with an object, the infrared receiver, which is a phototransistor, receives the waves. A phototransistor works like a normal transistor, except that its base is excited by light. Note This sensor works best for objects in the range of 0.2 to 1.5 cm. You can download the datashe...

SHT30 Temperature & Humidity Sensor Features SHT30 is a digital temperature and humidity sensor. This module uses I2C communication and the 2 SCL and SDA pins are used to communicate with this sensor. This sensor is ideal for temperature and humidity sensing.  Temperature measurement range: 0°C to 65°C/ Accuracy ±0.3°C Humidity measurement range: 0-100% RH/ Accuracy ±3% RH You can download the datasheet of this module here...

SHT35 Temperature and Humidity Sensor Features SHT35 is a digital temperature and humidity sensor. This module uses I2C communication protocol and the 2 SCL and SDA pins are used in order to communicate to this sensor. This sensor is ideal for temperature and humidity sensing. Temperature measurement range: -40°C to 90°C/ Accuracy ±0.2°C  Humidity measurement range: 0-100% RH/ Accuracy ±1.5% RH You can download the datasheet of this module here. [wpdm_packag...

L298N Motor Driver Module Features The L298N module is used to drive DC motors with a maximum current of 2 amps. The L298N driver module is easy to use. It contains a good filter circuit and gives you access access to inputs and outputs via pin headers and terminals. The L298N is a dual full-bridge motor driver that allows two DC motors to be connected simultaneously. Note The L298N motor controller follows the H-bridge configuration, which is handy to drive a stepper motors. This driver needs a logic vo...