Search results for: 'so module'

TLP281 4-Channel Opto-isolator IC Module Features Sometimes we need to separate the low-voltage section (microcontroller) from the high-voltage one in circuit in order to prevent noise and damage to the microcontroller. This module isolates the low-voltage section from the high-voltage section using TLP281-4 IC. This IC contains 4 LEDs (Light Emitting Diode). 4 high-voltage channels can be controlled by microcontroller using this IC.This module can also be used to turn on and off the servo motor and oth...

SI7021 Temperature and Humidity Sensor Features The SI7021 humidity and temperature sensor is a CMOS integrated sensor with I2C communication protocol. This sensor is factory calibrated and calibration data is stored in an on-chip non-volatile memory.This sensor is used in various applications such as thermostat and humidistats, respiratory therapy, Indoor weather stations, tablets, mobile phones, etc.Humidity measurement range: 0 to 100%RH - Accuracy 3%RHTemperature measuring range: -40°C to +125°C ...

SS49E Linear Hall Effect Sensor Features The output of SS49E linear Hall sensor provides an analog voltage representing if a magnetic field is present. So, this small and versatile sensor can be used in systems containing permanent magnets or an electromagnets in order to monitor magnetic field change. The output voltage is in the range of 2.25V to 2.75V. In this sensor, amplifier, voltage regulator and logic switching circuits are used to overcome noise in the output. SS49E Linear Hall Effe...

Interfacing AS608 Optical Fingerprint Sensor Module with Arduino provides a comprehensive guide on integrating the AS608 optical fingerprint sensor with Arduino for secure fingerprint scanning and identification. This step-by-step guide will walk you through the process of enrolling and verifying fingerprints using the AS608 module. Discover how to connect the module to Arduino, install the required library, and follow the enrollment and verification procedures. Get started on your fingerprint sensor projec...

SW-18010P Vibration Sensor Module Features The SW-18010P sensor is used to detect vibration. The sensor has a small spring inside a metal tube. When the sensor vibrates, the spring hits the metal tube and the sensor will be activated.This sensor has two digital and analog outputs. When the sensor vibrates, the digital output changes from HIGH to LOW and the analog output changes from 1023 to 0.Other features:Operating voltage: 3.3V to 5VIncluding a fixed hole on board for easy installationPotentiome...

GY-31 TCS3200 Color Sensor Features The TCS3200 color sensor uses 64 photodiodes to detect color. The output of this sensor is a square wave. Color intensity is obtained directly from the frequency of the square wave. These 64 photodiodes consist of 16 diodes with red filter, 16 diodes with green filter, 16 diodes with blue filter and 16 transparent photodiodes without filter. All 16 diodes of each type are connected in parallel. To detect any color, the photodiodes corresponding to that color are activ...

BMP280 Pressure Sensor Features The BMP280 barometric pressure module is a tiny sensor to measure barometric pressure. Its small dimensions and its low power consumption allow for the implementation in battery powered devices such as mobile phones, GPS modules or watches.The key features are:Pressure range: 300 to 1100 hPaCapable of measuring temperaturePressure measurement accuracy: 0.12 hPaSupport I2C communication up to 3.4 MHzSupport SPI communication up to 10 MHzApplications:Indoor navigationWeath...

Overview In this tutorial, you will learn how to use a soil moisture sensor. Practical examples are also provided to help you master the code. What You Will Learn How soil moisture sensors work How to use soil moisture sensor with Arduino Soil Moisture Sensor - How Does It Work? The soil moisture sensor consists of two probes that measure the volume of water in the soil. The two probes allow the electric current to pass through the soil and, according to its resistance,...

TTP224 Capacitive Touch Sensor Module Features This 4 Channel Capacitive Touch Sensor Module uses the TTP224 IC and is actually a combination of 4 capacitive touch sensors. This module has 4 outputs, by touching each button from 1 to 4, the corresponding output will be High. There are also 4 LEDs on the module that will turn on by touching each button. TTP224 Capacitive Touch Sensor Module Pinout This module has 12 pins and 4 touch buttons:6 pins on the Right:OUT1: ...

KY-039 Heartbeat Sensor Module Features The KY-039 heartbeat sensor module can be used to detect the heartbeat signal using finger. This sensor has an analog output. By placing your finger on the module, you can see the heartbeat signal through the analog output pin. KY-039 Heartbeat Sensor Module Pinout This module has 3 pins:S: Analog output signalVCC: Module power supply – 5VGND: GroundYou can see the pinout of this module here. ...