Search results for: 'on arduin arduino'

FC-04 Sound Sensor Features This module consists of a capacitive microphone and an amplifier circuit. The output of this module is analog. This module can be used to measure ambient noise. You can adjust the accuracy of the sensor by using a variable resistor on the device. FC-04 Sound Module Pinout FC-04 module has 3 pins: VCC: Module power supply: 5 V GND: Ground OUT: Module output (Analog) You can see the pinout in the following image. Required Materials Hardware C...

TCS230 Color Sensor Features The TCS230 chip reads an 8x8 array of photodiodes and uses them to recognize color. Sixteen photodiodes have blue filters, 16 photodiodes have green filters, 16 photodiodes have red filters, and 16 photodiodes are clear with no filters.The TCS230 module has 4 white LED. Photodiodes receive the light reflection of these LEDs from the surface of the object and generate an electric current depending on the color they receive.In addition to photodiodes, this sensor also has a cu...

MAX9814 Microphone Module Features Microphone AGC amplifier module, based on MAX9814 chip, has a 2.7V to 5.5V power supply. This device features a built-in low-noise microphone bias. This module can also be connected directly to AUX output. Note The module’s output is not zero in silent mode and has an offset 1.25V. MAX9814 Microphone Module Pinout This module has 5 pins:  VCC: Module power supply – 2.7-5.5 V  GND: Ground  OUT: Analog data output to the microcontroller ...

SRF05 Ultrasonic Module Features SRF05 is an ultrasonic transmitter and receiver module used to measure distance. The sensor operation is very simple. You only need to measure the return time of ultrasonic waves in order to measure the distance. Then you should divide measured time by 2 and multiply by the sound speed. The sensor measuring range is about 2 to 400 cm. You can download the datasheet of this module here. [wpdm_package id='17336'] SRF05 Ultrasonic Module Pinout This sensor has 3 pi...

801S Vibration Module Features The 801S vibration sensor module has a digital output pin that gives HIGH output by detecting vibration up to a certain threshold. The sensitivity of this sensor can be adjusted with a potentiometer on the module. The IC on this module is LM358. This module can be used in security systems. Note The module's sensitivity is very high. You can download the datasheet of this module here. [wpdm_package id='17349'] 801S Vibration Module Pinout This sensor has 3 pins: ...

US-100 Distance Sensor Features The US-100 is an ultrasonic transmitter and receiver module used to measure distance. The sensor operation is very simple. You only need to measure the return time of ultrasonic waves in order to measure the distance. Then you can divide this time by 2 and multiplied by the sound speed. The sensor measuring range is about 2 to 450 cm. Note The US-100 module has 2 different communication protocol. Method 1: use serial communication Method 2: use Trigger and Echo (similar to ...

MAX4466 Module Features The MAX4466 sensor is used to detect ambient sounds. This module has a built-in amplifier. Note The module output is not zero in silent mode and has 1.25V offset. MAX4466 Electret Microphone Pinout This sensor has 3 pins:VCC: Module power supply – 3-5.5 VGND: GroundOUT: Digital output data to the microcontrollerYou can see pinout of this module in the image below. You can download the datasheet of thi...

TM7711 24-bit Pressure Module Features The TM7711 is a 24-bit 2-channel analog-to-digital converter used to measure resistance changes. This module is widely used in load cell and air pressure sensors. This module features high accuracy, quality and cost-effectiveness. Note This module does not support I2C communication. You can download the datasheet of this module here. [wpdm_package id='18020'] TM7711 24-bit Pressure Module Pinout This sensor has 8 pins: VIN: Module power supply – 3.3-5...

DWM1000 Transceiver Module Features DWM1000 is an IEEE802.15.4-2011 UWB-compliant wireless transceiver module based on DecaWave’s DW1000 IC. DWM1000 measures location of objects using Real-Time Location Systems (RTLS) to a precision of 10cm indoors. This modules features a high data communication rate, up to 6.8 Mb/s, and has excellent communications range of up to 300m. It is also used in Wireless Sensor Networks (WSN). Tip You need at least 2 pieces of this sensor to use it. It is better ...

YwRobot Vibration Sensor Features Tilt sensors detect vibrations by having small metal spheres inside. You can use the generated signal to make an alarm if there is vibration. The output of this sensor is a digital signal. This Vibration Sensor is easy to interface with Arduino and you can use it to detect vibration. YwRobot Vibration Sensor Pinout This sensor has 4 pins:5V: Module power supply –2.4 V to 5 VGND: GroundOUT: OutputYou can see pinout of this module in...