Search results for: 'module in'

Buzzer Features A buzzer is a device used to produce sound. There are two types of buzzer: active and passive. In the active model, buzzer starts playing sound only if connected to a power supply, but in the passive model, we need to send a pulse from the microcontroller to play sounds. The supply voltage of the buzzer is 3 volts, 5 volts and 12 volts. You can download the passive buzzer datasheet here. [wpdm_package id='16469'] Passive Buzzer Module Pinout Buzzer has 2 pins: DATA and GND but t...

ACS712 Current Module Features ACS712 chip is used to measuer DC/AC current based on the Hall effect. This chip is produced in 3 models with different maximum currents. Different models and output sensitivity of each model are shown in the table below: Sensor sensitivity means that, for example, if you use 5 amp model, as input current increase 1 amp, the output voltage of the sensor increases about 185 mV. Note When input is not connected to something and th...

FC-04 Sound Sensor Features This module consists of a capacitive microphone and an amplifier circuit. The output of this module is analog. This module can be used to measure ambient noise. You can adjust the accuracy of the sensor by using a variable resistor on the device. FC-04 Sound Module Pinout FC-04 module has 3 pins: VCC: Module power supply: 5 V GND: Ground OUT: Module output (Analog) You can see the pinout in the following image. Required Materials Hardware C...

TEA5767 FM Radio Module Features The TEA5767 module is an FM radio receiver that can be connected to a microcontroller using the I2C protocol to search for radio stations. This module has a headphone output. You can download the TEA5767 FM Radio Module datasheet here. [wpdm_package id='16808'] TEA5767 FM Radio Module Pinout This Module has 4 pins:VCC: Module power supply - 5 VGND: GroundSLC: Synchronization for I2C protocolSDA: Data for I2C protocolYou can se...

DS18B20 Temperature Module Features DS18B20 module is a temperature sensor that can measure temperature in the range of -55°C to + 125°C with an accuracy of 0.5 ° C. The output accuracy of this sensor is adjustable from 9 to 12 bits which is set to 12 bits by default. The communication protocol of this sensor is one-wire, and to measure the ambient temperature you only need to connect one wire to Arduino. Using this module is quite similar to the DS18B20 Sensor since it based on that component. Note One...

MAX9814 Microphone Module Features Microphone AGC amplifier module, based on MAX9814 chip, has a 2.7V to 5.5V power supply. This device features a built-in low-noise microphone bias. This module can also be connected directly to AUX output. Note The module’s output is not zero in silent mode and has an offset 1.25V. MAX9814 Microphone Module Pinout This module has 5 pins:  VCC: Module power supply – 2.7-5.5 V  GND: Ground  OUT: Analog data output to the microcontroller ...

SRF05 Ultrasonic Module Features SRF05 is an ultrasonic transmitter and receiver module used to measure distance. The sensor operation is very simple. You only need to measure the return time of ultrasonic waves in order to measure the distance. Then you should divide measured time by 2 and multiply by the sound speed. The sensor measuring range is about 2 to 400 cm. You can download the datasheet of this module here. [wpdm_package id='17336'] SRF05 Ultrasonic Module Pinout This sensor has 3 pi...

801S Vibration Module Features The 801S vibration sensor module has a digital output pin that gives HIGH output by detecting vibration up to a certain threshold. The sensitivity of this sensor can be adjusted with a potentiometer on the module. The IC on this module is LM358. This module can be used in security systems. Note The module's sensitivity is very high. You can download the datasheet of this module here. [wpdm_package id='17349'] 801S Vibration Module Pinout This sensor has 3 pins: ...

BIOVO-C3 Fingerprint Module Features BIOVO-C3 optical fingerprint module is a high-precision, high-performance matching algorithm and high-capacity flash chip. It works based on fingerprint image processing, matching, memory search and performance and desired functions. It uses serial communication in order to communicate with microcontroller. The default Baud Rate is 57600, and it can not be changed. It can store up to 200 fingerprint samples and you can directly connect it to a computer via USB. ...