Search results for: 'modul to with'

YwRobot Vibration Motor Features This small built-in module uses a high-quality vibration motor. You can make some interesting Arduino projects such as an alarm, a notifier or even a vibrating robot! When the input is high, the motor will vibrate just like your cell phone. You can control the ON/OFF or vibration intensity through digital signal or PWM signal.The module adopts a high-quality mobile phone vibration motor; the vibration effect is evident; it is amplified and suitable as a non-audible indic...

Vibration Motor Module Features This small built-in module uses a high-quality vibration motor. You can make some interesting Arduino projects such as an alarm, a notifier or even a vibrating robot! When the input is high, the motor will vibrate just like your cell phone. You can control the ON/OFF or vibration intensity through digital signal or PWM signal. The module adopts a high-quality mobile phone vibration motor; the vibration effect is evident, it is amplified...

YwRobot Touch Sensor Module Features Touch Sensor is used to detect human finger touch. It is known as a touch switch as well. These sensors are easy to use and useful in many projects. Before touching the sensor, the output signal is always HIGH. When a human finger touches the sensor, it will generate a LOW level signal. This module also has an LED that lights up when the sensor is touched. Note This module works in trigger mode. That is when the sensor is touched, the digital output is LOW a...

Double-sided Touch Sensor Features There is a wide variety of touch sensors. One of these sensors is double-sided touch sensor with 3-pin and 4-pin interface on each side. Pin N in 4-pin interface is not used. Note Pin S is always HIGH and changes to LOW if the switch is touched. (If not touched, it will be HIGH again.) Double-sided Touch Sensor Pinout This Module has 3 main pins:VCC: Module power supply – 3.3/ 5 VGND: GroundS: Sensor output (5V)N: Not us...

OE-TP Light Touch Switch Module Features This module has a fingerprint sensor that can control the digital output voltage. So The output voltage will change with each touch. The operating voltage is 5 to 20 V (recommended 12 volts) and operating current is up to 3 A (peak 10 A). It also has two red and blue LEDs. The blue LED indicates the module is powered on and the red LED indicates touch detection.This type of sensor is widely used in home lighting, motor speed control, toys, etc. ...

Touch Switch Module Features A touch sensor is a type of switch that needs to be touched by an object to operate. Touch sensors work completely similar to a switch. Note When this switch is touched, the output voltage will be HIGH, otherwise is LOW. Note The output current is very low (about 40 mA). If you want to connect a higher current device to this switch, you must add a relay or transistor to your circuit. Note There is a jumper on the board. If you change the status ...

TLP281 4-Channel Opto-isolator IC Module Features Sometimes we need to separate the low-voltage section (microcontroller) from the high-voltage one in circuit in order to prevent noise and damage to the microcontroller. This module isolates the low-voltage section from the high-voltage section using TLP281-4 IC. This IC contains 4 LEDs (Light Emitting Diode). 4 high-voltage channels can be controlled by microcontroller using this IC.This module can also be used to turn on and off the servo motor and oth...

L9110 Dual Channel Driver Module Features Motor driver modules are very common nowadays and widely used to control the speed and direction of motors. The L9110S dual channel module is one of them. This module can control two DC motors and one stepper motor. It is based on L9110 IC. The key features are:The allowable continuous current for each channel:  800mA.The operating voltage: 2.5 - 12V.Two control pins for each DC motor.Suitable for toy cars motors.Can control one stepper motor. ...

L9110S Dual-Channel Driver Module Features Motor driver modules are very common nowadays and widely used to control the speed and direction of motors. The L9110S dual-channel module is one of them. This module can control two DC motors and one stepper motor. It is based on L9110 IC. The key features are: The allowable continuous current for each channel: 800 mA The maximum allowable current: 1.5 A Power supply: 2.5V to 12V Note The two connected pins to each DC motor can be PWM or digital. If define...

Learn how to interface the BTS7960 43A high-power motor driver module with Arduino. This guide covers the key features of the BTS7960 motor driver, its pinout configuration, and provides step-by-step instructions for circuit connection and code implementation. Take control of your motors with this versatile and powerful motor driver. BTS7960 43A Motor Driver Features The BTS7960 is a high-current full-bridge motor driver module. The Key features are: Input voltage: 6V to 27V Maximum allowable current: ...