Search results for: 'with a'

DRV8833 Dual Motor Driver Features Today, speed and direction control of DC motors is very important and useful. The H-bridge circuit is one of the most common techniques to control a DC motor. The DRV8833 dual-channel module uses this technique to control two DC motors.This dual H-bridge motor driver can drive two DC motors, a stepper motor or other inductive loads.The driver supply voltage is 2.7 to 10.8V and the allowable continuous current is 1.5A and the maximum allowable current is 2A.Some common...

74HC4051 8-Channel Analog Multiplexer Features The 74HC4051 8-Channel analog multiplexer module can be used when there are many analog inputs in a circuit. In this case, one of these inputs needs to be selected and processed each time. This multiplexer can be used to select from 8 analog inputs. There are three S0-2 pins, which by giving appropriate values, one of the analog inputs is set as the output on the Z pin. 74HC4051 8-Channel Multiplexer Pinout This module ...

2.2 INCH Full Color TFT Display Features The TFT display is a kind of liquid crystal display that is connected to each pixel using a transistor and it features low current consumption and backlight. This 2.2-inch full color LCD has a narrow PCB screen. The resolution is 320x280 pixels and it has a four-wire SPI interface and white backlight.This display also has a touch screen and SD card slot. Note The module voltage is 3.3 V and a voltage divider is required to interface it with Arduino. ...

A4988 Stepper Motor Driver Features The A4988 stepper motor driver is intended to drive a bipolar stepper motor. Only by two pins, you can control the rotation direction and rotation steps. Each signal sent by the spin step pin, the motor rotates one step. The key features are:This driver has 200 steps per revolution in full step (1.8 degrees per step).Allowable continuous current per phase without cooling: 1AMaximum current per phase with cooling: 2AMotor voltage: 8 to 35 VThe minimum allowed pulse�...

TMC2100 Stepper Motor Driver Features The TMC2100 driver is one of the most popular stepper motor drivers available on the market. It works similar to the DRV8825 and A4988 drivers.This module is intended to drive a bipolar stepper motor. Only by using two pins, the rotation direction and rotation steps can be controlled. Each signal sent by the spin step pin, the motor shifts one step. The key features are:This driver has 200 steps per revolution in full step (1.8 degrees per step).Allowable continuou...

PN532 NFC RFID Module Features If you are experienced in electronics, you have probably heard of RFID (radio-frequency-identification) and NFC (near-field-communication). PN532 module is a kind of RFID-NFC module that uses I2C, SPI and HSU protocols for communication. This module is based on NXP PN532 IC. The key features are:Support I2C, SPI, high-speed UART (HSU) protocolsPCB design for antennaCommunication distance: 5 to 7cmRFID reader and writer supports the following:Mifare 1K 4K, Ultralight and ...

2.8 INCH TFT LCD Display Features The TFT display is a kind of LCD that is connected to each pixel using a transistor and it features low current consumption, high-quality, high-resolution and backlight. This 2.8-inch full color LCD has a narrow PCB display. The resolution is 320x280 pixels and it has a four-wire SPI interface and white backlight. This display also has a touch screen and SD card slot. Note The module voltage is 3.3V and voltage divider is required to interface it with Arduino. ...

Focusable Red Line Laser Features This module emits a small intense focused beam of visible red light. This module can be used in fiber optic communications, laser test tools, surgical equipments, GPS tracking, etc. At the top of the laser there is a screw that is used to adjust the laser light. Some key features are:Operating voltage: 3VRequired current for module to be turned on: Less than 40mAOutput power: 5mWLaser wavelength: 650nm Note Since the required current is less than 40mA and the ...

DS1307 RTC Module Features The DS1307 real time clock module can be used for keeping date in different projects. This RTC module provides seconds, minutes, hours, day, date, month, and year information. In this module, the date is set automatically based on whether the month is 29, 30 or 31 days, and also whether it is leap year or not. This RTC module can communicate with different microcontrollers using the I2C communication protocol.The DS1307 RTC module is available on the market in two different v...

DS1302 RTC Module Features for Accurate Timekeeping The DS1302 real time clock module is a cheap module with high accuracy that can be used in different projects. This RTC module provides seconds, minutes, hours, day, date, month, and year information. In this module, date is set automatically based on whether the month is 29, 30 or 31 days and also it is leap year or not. (That's only valid until the year 2100) Note Please be aware that this module does not use I2C communication. Interfacing the DS1302 wi...