Search results for: 'or arduino'

DRV8833 Dual Motor Driver Features Today, speed and direction control of DC motors is very important and useful. The H-bridge circuit is one of the most common techniques to control a DC motor. The DRV8833 dual-channel module uses this technique to control two DC motors.This dual H-bridge motor driver can drive two DC motors, a stepper motor or other inductive loads.The driver supply voltage is 2.7 to 10.8V and the allowable continuous current is 1.5A and the maximum allowable current is 2A.Some common...

A4988 Stepper Motor Driver Features The A4988 stepper motor driver is intended to drive a bipolar stepper motor. Only by two pins, you can control the rotation direction and rotation steps. Each signal sent by the spin step pin, the motor rotates one step. The key features are:This driver has 200 steps per revolution in full step (1.8 degrees per step).Allowable continuous current per phase without cooling: 1AMaximum current per phase with cooling: 2AMotor voltage: 8 to 35 VThe minimum allowed pulse�...

TMC2100 Stepper Motor Driver Features The TMC2100 driver is one of the most popular stepper motor drivers available on the market. It works similar to the DRV8825 and A4988 drivers.This module is intended to drive a bipolar stepper motor. Only by using two pins, the rotation direction and rotation steps can be controlled. Each signal sent by the spin step pin, the motor shifts one step. The key features are:This driver has 200 steps per revolution in full step (1.8 degrees per step).Allowable continuou...

DRV8825 Stepper Motor Driver Features The DRV8825 module is used to drive a bipolar stepper motor. Only by two pins, you can control the rotation direction and rotation steps of the motor. By each signal sent by the spin step pin, the motor shifts one step. The key features are:This driver has 200 steps per revolution in full step (1.8 degrees per step).Allowable continuous current per phase without cooling: 1.5AMaximum current per 24V for each phase: 2.5AMotor voltage: 8.2 to 45VThe minimum allowed ...

1.8 Inch SPI TFT Color Display Features TFT display is a kind of liquid crystal LCD that is connected to each pixel using a transistor and it features low current consumption, high-quality, high-resolution and backlight. This 1.8 inch full color LCD has a narrow PCB screen. The resolution is 128x160 pixels and it has a four-wire SPI interface and white backlight. The driver is ST7735.This display also has a SD card slot. Note The operating voltage of this module is 3.3V and voltage divider is r...

ZMCT103C Current Transformer Module Features The ZMCT103C AC current transformer module can be used to monitor current in various applications. This module is based on ZMCT103C IC. The mechanism of this IC is that the wire whose current is to be measured, passes through the hole of the IC. Then, according to AC current, voltage is induced on both sides of IC.In this module, the output voltage of ZMCT103C IC is amplified by a series of amplifiers and can be used as the module output. The module outputs ...

1.3 INCH OLED IPS Display Module Features OLED displays offer many advantages in compare to LCDs and LEDs. These full color modules are high-quality. This 1.3 inch OLED display has SPI communication protocol. The resolution is 240x240, which means it contains 57,600 pixels. So, it enjoys a clear and transparent display quality. 1.3 INCH OLED IPS Display Module Pinout This module has 7 pins:GND: GroundVCC: Module power supply – 3.3 VSCL: SPI clockSDA: SPI dataRE...

LM393 Voltage Comparator Module Features The LM393 amplifier module can be used to compare an input voltage with a predetermined voltage level. The LM393 IC contains 2 op-amps that are completely independent. In LM393 comparator module, only one of the op-amps is used and the other is not connected. The module compares input voltage with the desired voltage level, and produces a digital output. The voltage level can be any value between the module positive and negative supply voltages. This voltage lev...

SS49E Linear Hall Effect Sensor Features The output of SS49E linear Hall sensor provides an analog voltage representing if a magnetic field is present. So, this small and versatile sensor can be used in systems containing permanent magnets or an electromagnets in order to monitor magnetic field change. The output voltage is in the range of 2.25V to 2.75V. In this sensor, amplifier, voltage regulator and logic switching circuits are used to overcome noise in the output. SS49E Linear Hall Effe...

IR Flame Sensor Analog Output Features This flame sensor module with analog output can be used to detect flames. You can easily connect this module to a variety of microcontrollers and make a device to detect fire. The output is an analog voltage, whose maximum value is 5 volts and will decrease as the flame increases. IR Flame Sensor Analog Output Pinout This Module has 3 pins:OUT: Analog OutputVCC: Module power supply – 5VGND: GroundYou can see the pinout of thi...