Search results for: 'RF MODULE'

SW-18010P Vibration Sensor Module Features The SW-18010P sensor is used to detect vibration. The sensor has a small spring inside a metal tube. When the sensor vibrates, the spring hits the metal tube and the sensor will be activated.This sensor has two digital and analog outputs. When the sensor vibrates, the digital output changes from HIGH to LOW and the analog output changes from 1023 to 0.Other features:Operating voltage: 3.3V to 5VIncluding a fixed hole on board for easy installationPotentiome...

GY-31 TCS3200 Color Sensor Features The TCS3200 color sensor uses 64 photodiodes to detect color. The output of this sensor is a square wave. Color intensity is obtained directly from the frequency of the square wave. These 64 photodiodes consist of 16 diodes with red filter, 16 diodes with green filter, 16 diodes with blue filter and 16 transparent photodiodes without filter. All 16 diodes of each type are connected in parallel. To detect any color, the photodiodes corresponding to that color are activ...

BMP280 Pressure Sensor Features The BMP280 barometric pressure module is a tiny sensor to measure barometric pressure. Its small dimensions and its low power consumption allow for the implementation in battery powered devices such as mobile phones, GPS modules or watches.The key features are:Pressure range: 300 to 1100 hPaCapable of measuring temperaturePressure measurement accuracy: 0.12 hPaSupport I2C communication up to 3.4 MHzSupport SPI communication up to 10 MHzApplications:Indoor navigationWeath...

Overview In this tutorial, you will learn how to use a soil moisture sensor. Practical examples are also provided to help you master the code. What You Will Learn How soil moisture sensors work How to use soil moisture sensor with Arduino Soil Moisture Sensor - How Does It Work? The soil moisture sensor consists of two probes that measure the volume of water in the soil. The two probes allow the electric current to pass through the soil and, according to its resistance,...

TTP224 Capacitive Touch Sensor Module Features This 4 Channel Capacitive Touch Sensor Module uses the TTP224 IC and is actually a combination of 4 capacitive touch sensors. This module has 4 outputs, by touching each button from 1 to 4, the corresponding output will be High. There are also 4 LEDs on the module that will turn on by touching each button. TTP224 Capacitive Touch Sensor Module Pinout This module has 12 pins and 4 touch buttons:6 pins on the Right:OUT1: ...

KY-039 Heartbeat Sensor Module Features The KY-039 heartbeat sensor module can be used to detect the heartbeat signal using finger. This sensor has an analog output. By placing your finger on the module, you can see the heartbeat signal through the analog output pin. KY-039 Heartbeat Sensor Module Pinout This module has 3 pins:S: Analog output signalVCC: Module power supply – 5VGND: GroundYou can see the pinout of this module here. ...

HW-M10 Microwave Sensor Module Features The HW-M10 microwave sensor module is very accurate and widely used for motion detection in alarm and security systems. This module, like the PIR module, can detect any movement. The only difference is that instead of using radiation emitted by or reflected from objects, it uses microwave Doppler radar technology. This module has a digital output that is normally Low and becomes High (3.3V) if it detects motion and remains High for 2 to 3 seconds. ...

MPR121 Capacitive Touch Sensor Features The MPR121 capacitive touch sensor module is a high-precision touch sensor. This module has 12 touch buttons and supports I2C communication and can be easily interfaced with any microcontroller. There is no regulator on the board, so the supply voltage should be between 1.7 to 3.6VDC. MPR121 Capacitive Touch Sensor Pinout This module has 18 pins:6 Pins on the left:VCC: Module power supply – 3.3VIRQ: Interrupt outputSCL: Se...

RDM6300 RFID Reader Module Features If you are a little familiar with electronics then you have probably heard of RFID (Radio-Frequency-Identification). The RDM6300 model is one type of RFID modules with 125 kHz frequency. This module is designed for reading code from 125KHz (ID) compatible read-only tags and read/write 125KHz cards.Features:Support external antennaMaximum effective distance: up to 50 mmUart interfaceSmall outline design RDM6300 RFID Reader Module Pin...

If you're looking to interface the INA219 current sensor module with an Arduino, you've come to the right place. In this guide, we'll walk you through the necessary steps to get your setup up and running smoothly. INA219 Current Sensor Module Features The INA219 module is used to measure both current and voltage at the same time. This module uses I2C communication to transfer the voltage and current data. Other features: Measurement accuracy: 1% Maximum measured voltage: 26V Maximum measured current...