Search results for: 'interfacing arduino'

LJ12A3-4-Z/BX Inductive Proximity Sensor Features Proximity sensors are used to detect the presence of nearby objects. The LJ12A3-4-Z / BX sensor has three pins, two of which are connected to a supply voltage of 6 to 36 V. The output pin is PNP and NO (Normal Open). That is, it is normally Low and when it detects an object, it becomes HIGH. The detection distance is 4 mm, and it can only detect metal objects such as copper, aluminum, iron, etc. Note Since the operation voltage is more than 5 V,...

L298P Motor Driver Shield Features Today, DC motors are used in the manufacturing many tools and equipments. So, speed and direction control of these motors is very common. A half-bridge circuit is one of the simplest methods to control a DC motor. This method not only controls the motor direction, but also can be used for speed control. This shield is based on L298P IC. The most important features are: Control two DC motors simultaneously with voltage 4.8 to 24V and up to 2A current Schottky diodes ...

Learn how to interface a 4x3 membrane matrix keypad with Arduino using this comprehensive tutorial. By following the steps outlined below, you can easily connect the keypad to your Arduino and start using its 12 buttons with only 7 pins on the microcontroller. Features of the 4x3 Matrix Keypad Keypads are one of the most popular components that are widely used in electronics. Everybody can communicate with the system by switches. Normally, every key occupies one digital pin of the microcontroller. But by us...

4-bit Button Touch Proximity Sensor Features This module has 4 fingerprint touch inputs and 4 digital output pins. It also has 5 LEDs. One for power supply and 4 LEDs indicate fingerprint sensors. If you touch each sensor, the output becomes HIGH and the LED turns on. If you don’t touch, the output will be LOW and the LED turns off.This module can be used on glass, ceramic, plastic and other surfaces. 4-bit Button Touch Proximity Sensor Pinout This module has 6 pi...

TTP223 Capacitive Touch Sensor Features The TTP223 sensor can be used in a variety of applications such as smartphones and tablets. The sensor can recognize objects even from behind glass and thin surfaces. The operating voltage is 2 to 5.5V. The maximum response time is 220 milliseconds. This module has two non-soldered adjustment pins: A and B. The working modes are as follows:A and B both open: The default value of the output pin is LOW. When the sensor is subjected to touch, the output is HIGH, and...

SI7021 Temperature and Humidity Sensor Features The SI7021 humidity and temperature sensor is a CMOS integrated sensor with I2C communication protocol. This sensor is factory calibrated and calibration data is stored in an on-chip non-volatile memory.This sensor is used in various applications such as thermostat and humidistats, respiratory therapy, Indoor weather stations, tablets, mobile phones, etc.Humidity measurement range: 0 to 100%RH - Accuracy 3%RHTemperature measuring range: -40°C to +125°C ...

OMRON Photoelectric Sensor Features The Omran photoelectric sensor can be used to detect obstacles and objects at 5 to 100 mm distance. There is an LED on the sensor that is always off and turns on when it detect an obstacle. You can also change the LED status using the potentiometer which is on sensor. (That is, the LED is always on and will turn off when the obstacle is detected.) There is another potentiometer on the sensor that can be used to change the sensitivity of the sensor (increase or decrease th...

X9C103S Digital Potentiometer Module Features The X9C103S 10k digital potentiometer module is a variable resistor whose resistance value can be varied digitally from a microcontroller. It consists of a 3-pin output which can replace a mechanical potentiometer which has 3 pins. This module has 99 resistance components and the final resistor is controlled by a 3-wire interface. X9C103S Digital Potentiometer Module Pinout This sensor has 8 wires:VCC: Module power suppl...

TTP229 Capacitive Touch Keypad Features Keypads are one of the most popular components that are widely used in electronics. Everybody can communicate with different systems by switches. Normally, every key occupies one digital pin of the microcontroller. But by using a 4x4 keypad you can reduce the occupied pins. With this module, you can use all 16 switches by occupying only 2 pins of the microcontroller. This 16 key capacitive touch keypad is based on the TTP229 IC. Output pins 1 to 8 are for direct swit...

Dual-Axis Joystick Shield Features The dual-axis joystick shield is commonly used in robotics and game consoles. This module includes a 2-Axis joystick, 4 large buttons, 2 small buttons and a number of pins to connect to other components.The key features of this joystick are:A joystick in both X and Y directions4 buttons with plastic cover in 4 different directions2 separate small buttonsSerial / Bluetooth interfaceI2C interfacenRF24L01 interfaceConnection pins to nRF24L01 moduleNokia 5110 LCD interfac...